Bendix Recommends Choosing High Performance Friction When Servicing Brakes Designed To Meet Reduced Stopping Distance Mandate
ELYRIA, OH… Bendix Spicer Foundation Brake LLC (BSFB), responding to industry confusion about the performance of replacement brake linings in the new Reduced Stopping Distance (RSD) era, recently completed stopping-distance testing and analysis of RSD-compliant brakes relined with a range of aftermarket friction products. Based on its findings, the company strongly recommends choosing like-for-like OE friction when replacing the linings on Bendix brakes engineered to meet the federal RSD mandate. Doing so allows fleets to maintain RSD compliance and helps improve fleet “At Bendix, highway safety is our passion and at the forefront of our thinking,” said Eddie Wilkinson, BSFB president. “We have invested millions of dollars in R&D to develop new brake designs that meet and exceed the government mandate for reduced stopping distances on new vehicles. Since these vehicles will continue to share our roads after servicing, it’s vital that we help fleet operators make informed decisions to maintain that same high level of safety and performance.”
In August 2011, the National Highway Traffic Safety Administration (NHTSA) mandated a 30 percent reduction in stopping distance for new three-axle tractors with Gross Vehicle Weight Ratings (GVWRs) up to 59,600 lbs. RSD is meant to significantly improve safety, avoid highway fatalities, and reduce the number of rear-end collisions. Phase two of the mandate, aimed at tractors with two axles, as well as severe service tractors with GVWRs above 59,600 lbs., takes effect Aug. 1, 2013.
“We spend a great deal of time talking to our fleet customers, and through that ongoing dialogue have come to realize some general misunderstanding exists concerning maintenance of the new High Performance brakes,” said Gary Ganaway, director of marketing and global customer solutions for BSFB. “Bendix wants to make sure the industry understands the impact on stopping distance, so we conducted testing and analysis to demonstrate the potential trade-off in performance.”
Ganaway pointed out that the longtime industry standard test for certifying brake linings, Federal Motor Vehicle Safety Standard (FMVSS) 121, is no longer adequate in the RSD environment. Most linings that pass the dynamometer requirements do not meet today’s higher vehicle performance requirements.
Bendix compared the 60 mph stopping distance of an RSD-compliant vehicle equipped with high performance brakes and linings against several pre-RSD OE brake linings. The RSD-compliant vehicle used Bendix® High Performance ES™ (Extended Service) Brakes. Bendix High Performance Friction had a stopping distance of 215 feet, well under the 250-foot limit established by the federal mandate.
None of the comparison friction used in the relining of the RSD brakes met the stopping distance requirement. The worst-performing friction material, a popular aftermarket lining, had a stopping distance of 311 feet, a 45 percent decrease in performance from the Bendix friction. The 96-foot difference represents approximately five passenger car lengths.
Delivering lower fade and better thermal management, High Performance (HP) Friction from Bendix performs at high heat better than any previous OE drum brake linings, resulting in significantly shorter stopping distances.
“When our engineers develop brake systems, they also specify the friction material as an integral part of each design. Prior generation friction material formulations available throughout the industry are simply not engineered to this same performance standard,” Ganaway said. “To avoid confusion and potential risks to safety, we strongly encourage replacing friction like-for-like when relining Bendix High Performance ES Brakes. By doing so, fleets will have the peace of mind that comes from maintaining braking capability, helping to mitigate risk and achieve an attractive return on investment.”
Bendix’s brake solutions are part of the company’s ever-growing portfolio of technology developments that delivers on safety, plus other areas critical to fleets’ success.
“We are not satisfied with delivering technology just for technology’s sake,” Wilkinson said. “Our development criteria mean we must not only help lower the total cost of ownership, but also help improve vehicle performance and efficiency. We are working to couple this with robust post-sales support to deliver complete braking solutions for today’s fleet operators.”
For more information about Bendix High Performance Friction, call 1-800-AIR-BRAKE or visit www.foundationbrakes.com.